You're viewing a previously published revision of this guide.  View latest revision

Older
Dec 15, 2021 - 05:12:42
Feb 04, 2022 - 12:02:47 Jan 22, 2022 - 07:01:46 Dec 28, 2021 - 11:12:56 Dec 25, 2021 - 06:12:08 Dec 25, 2021 - 04:12:28 Dec 20, 2021 - 09:12:20 Dec 20, 2021 - 08:12:12 Dec 16, 2021 - 09:12:25 Dec 15, 2021 - 07:12:05 Dec 15, 2021 - 07:12:59 Dec 15, 2021 - 07:12:04 Dec 15, 2021 - 07:12:07 Dec 15, 2021 - 07:12:07 Dec 15, 2021 - 07:12:15 Dec 15, 2021 - 06:12:44 Dec 15, 2021 - 05:12:11 Dec 15, 2021 - 05:12:18 Dec 15, 2021 - 05:12:39 Dec 15, 2021 - 05:12:20 Dec 15, 2021 - 05:12:42 Dec 15, 2021 - 04:12:53 Dec 15, 2021 - 04:12:46 Dec 15, 2021 - 04:12:59 Dec 15, 2021 - 03:12:02 Dec 15, 2021 - 03:12:55 Dec 15, 2021 - 03:12:51 Dec 15, 2021 - 03:12:48
Newer

03. Y-Axis Motor Assembly

Written By: Simon Davie (and one other contributor)
  • Comments: 0
  • Favorites: 0
  • Completions: 18

Steps

3

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

User-Contributed Guide

User-Contributed Guide

This guide is not managed by the site's staff.

Quiz

0

  1. 1x 40mm NEMA17 Stepper Motor

    • 1x 40mm NEMA17 Stepper Motor

    • y_motor_cage printed part

    • 4x M6x12 Cap Head Screw

    • 4x M3x8 Cap Head Screw

    • 1x 20 Tooth 2GT Timing Pulley for 9mm Belt

    • 4x 3030 Square T-Nut - M6

    • 1x M8x30 Cap Head Screw

  2. y_motor_cage printed part M6x12 Cap Head Screw 3030 Square T-Nut - M6

    • y_motor_cage printed part

    • M6x12 Cap Head Screw

    • 3030 Square T-Nut - M6

    • Loosely thread the 3030 T-Nuts onto the M6x12 screws. Do not tighten them at this point.

    • 40mm NEMA17 Stepper Motor

    • Fasten the M3x8 screws to secure the stepper motor to the mount

    • Take care not to over tighten the M3x8 screws as you can damage the printed part

  3. Assembly from Step 2 20 Tooth 2GT Timing Pulley for 9mm Belt Position the timing pulley as shown. The end of the stepper shaft should be flush with the end of the pulley

    • Assembly from Step 2

    • 20 Tooth 2GT Timing Pulley for 9mm Belt

    • Position the timing pulley as shown. The end of the stepper shaft should be flush with the end of the pulley

    • Fasten the two grub screws on the timing pulley to secure it to the stepper motor shaft

Author

with 1 other contributor

Simon Davie

Member since: 8/5/21

27,210 Reputation

56 Guides authored

View Statistics:

Past 24 Hours: 1

Past 7 Days: 11

Past 30 Days: 111

All Time: 13,399