Introduction
Please note: This guide is based upon using two 80mm spindle mounts and an 80mm spindle. The required mounts, and number of them, will depend on your choice of spindle.
-
-
In the pursuit of a sturdier machine, Rat Rig updated the Z plate allowing for a stiffer spindle mount, the Rat Rig spindle mount!
-
Carefully identify your Z plate layout:
-
Z Plate V1.0 - compatible only with the Openbuilds spindle mount
-
Z Plate V1.1 - compatible only with the Rat Rig spindle mount
-
-
-
Identify the spindle mount included in your kit:
-
-
-
-
-
2x OpenBuilds Style Spindle Mount - 80mm
-
8x 90 Degree Corner Connector
-
4x M5x20 Cap Head Screw - Low Profile
-
8x M5x8 Button Head Screw
-
8x M5x10 Button Head Screw
-
-
-
OpenBuilds Style Spindle Mount - 80mm
-
M5x20 Cap Head Screw - Low Profile
-
Insert an M5x20 screw through each hole in the spindle mount front and secure it into the spindle mount body
-
Do not fully fasten the M5x20 screws at this point. They will be used to hold the spindle in place later in the assembly
-
-
-
90 Degree Corner Connector
-
M5x8 Button Head Screw
-
Insert an M5x8 screw through each 90 degree corner connector and fasten fully into the spindle mount
-
-
-
Spindle mount assembly from the previous step
-
90 Degree Corner Connector
-
M5x8 Button Head Screw
-
Insert an M5x8 screw through each 90 degree corner connector and fasten fully into the spindle mount
-
-
-
Spindle Mount Assembly
-
Align the spindle mount with the M5 threaded holes on the Z-axis
-
M5x10 Button Head Screw
-
Insert an M5x10 screw through each 90 degree corner connector and tighten into the threads on the Z-axis
-
Check that the spindle mount is flush and square with the Z-axis plate as shown
-
-
-
M5x10 Button Head Screw
-
Insert an M5x10 screw through each 90 degree corner connector and tighten into the threads on the Z-axis
-
-
-
Repeat the instructions in Steps 5 & 6 to install the top spindle mount
-
-
-
80mm Spindle
-
Insert the spindle into the mounts as shown
-
M5x20 Cap Head Screw - Low Profile
-
Tighten the M5x20 screws to secure the spindle in to the mounts
-
-
-
Rat Rig 80mm Spindle Mount
-
4x M6x70 Cap Head Screw
-
4x M6 Square nut
-
4x M8x30 Low Profile Cap Head Screw
-
2x M8x12 Low Profile Cap Head Screw
-
12x M8x22 Cap Head Screw
-
-
-
Rat Rig Spindle Mount - 80mm
-
M8x30 Low Profile Cap Head Screw
-
M8x12 Low Profile Cap Head Screw
-
Insert the screws through each hole in the spindle mount and secure it into the spindle mount body
-
-
-
Assembly from the previous step
-
M6x70 Cap Head Screws
-
Square nut M6
-
Do not fully fasten the M6x70 screws at this point. They will be used to hold the spindle in place later in the assembly
-
-
-
Spindle mount assembly
-
M8x22 Cap Head Screws
-
Place the screws in the designated holes, they will be tightened on the next step.
-
-
-
Spindle Mount Assembly
-
Mount the Spindle mount assembly on to the Z-Axis
-
Tighten the M8x22 screws
-
-
-
Repeat the instructions in Steps 5 to install the top spindle mount
-
-
-
80mm Spindle
-
Insert the spindle into the mounts as shown
-
Tighten the M6x70 screws to secure the spindle in to the mounts
-
-
-
When assembling the cooling circuit for your rig with a water-cooled spindle, please take this tip into account.
-
Allow the liquid hoses to move freely by themselves, do not constrain their movement.
-
Do not insert them into the drag chains, as the constricted pathways and tight bends may potentially result in punctures or leaks, thereby leading to machine malfunction.
-
Cancel: I did not complete this guide.
2 other people completed this guide.
