Pending Edits to 12. Enclosure Panels

Note: Accepting or denying any edit implicitly applies to all earlier pending edits to the same step or introduction.

Step #10 edited: [Step edited]

Edited by Giacomo (1)

(You don’t have enough reputation to patrol this edit.)

[title] Prepare the panel accessory parts
[* 2] 2x 3030_panel_mount_horizontal printed part
[* 3] 2x M6x12 Cap Head Screw
[* 4] 2x 3030 Drop-in T-Nut - M6
-[* 5] 10x Frame magnet mount assembly
+[* 5] 10x panel_magnet_mount assembly
[* 6] 1x Adhesive backed foam sealing tape

Step #8 edited: [Step edited]

Edited by shawn (1)

(You don’t have enough reputation to patrol this edit.)

[title] Assemble the side & back panels - Part 1
-[* 2] panel_enc2_side_***''size''***
+[* 2] panel_enc2_side_***''500''***
[* 3] M6 Washer
[* 4] M6x12 Cap Head Screw
[* 5] 3030 Drop-in T-Nut - M6
[* 10] Loosely thread the 3030 T-Nuts onto the M6x12 screws. Do not tighten them at this point.

Step #6 edited: [Step edited]

Edited by shawn (1)

(You don’t have enough reputation to patrol this edit.)

[title] Assemble the top panel
-[* 2] panel_enc2_top_***''size''***
+[* 2] panel_enc2_top_***''500''***
[* 3] Install four of the panel magnet mount assemblies to the top panel
[* 9] Take care not to over tighten the M6x12 screw as you can damage the printed parts
[* 4] Install two of the Rat Rig nylon handles to the top panel
[* 9] Do not overly tighten the M6 nylon locking hex nuts when securing the handles, as this can cause the panel to warp which will prevent a good seal to the printer
[* 10] Set the completed top assembly aside until ***Step 16***

Step #4 edited: [Step edited]

Edited by shawn (1)

(You don’t have enough reputation to patrol this edit.)

[title] Assemble the door panel - Part 2
[* 10] There are 2 handle positions on the door. Repeat the following for each of them
-[* 2] panel_enc2_door_***''size''***
+[* 2] panel_enc2_door_***''500''***
[* 3] Rat Rig nylon door handle
[* 4] M6x16 Cap Head Screw
[* 5] M6 Nylon Locking Hex Nut
[* 9] Do not overly tighten the M6 nylon locking hex nuts when securing the handles, as this can cause the panel to warp which will prevent a good seal to the printer

Step #3 edited: [Step edited]

Edited by shawn (1)

(You don’t have enough reputation to patrol this edit.)

[title] Assemble the door panel - Part 1
[* 10] There are 6 magnet mount positions on the door (or 4 on the 200). Repeat the following for each of them
-[* 2] panel_enc2_door_***''size''***
+[* 2] panel_enc2_door_***''500''***
[* 3] M6x12 Cap Head Screw
[* 4] M6 Washer
[* 5] Panel magnet mount assembly
[* 9] Take care not to over tighten the M6x12 screw as you can damage the printed parts

Step #2 edited: [Step edited]

Edited by Giacomo (1)

(You don’t have enough reputation to patrol this edit.)

[title] Prepare the enclosure panel parts
[* 2] 4x Rat Rig nylon door handle
-[* 3] 10x Panel magnet mount assemblies
+[* 3] 10x panel_magnet_holder assemblies
[* 4] 8x M6x16 Cap Head Screw
[* 5] 8x M6 Nylon Locking Hex Nut
[* 6] 24x M6x12 Cap Head Screw
[* 7] 24x M6 Washer

Step #1 edited: [Step edited]

Edited by shawn (1)

(You don’t have enough reputation to patrol this edit.)

[title] Prepare the enclosure panels
-[* 2] 2x panel_enc2_side_***''size''***
-[* 3] 1x panel_enc2_door_***''size''***
-[* 4] 1x panel_enc2_top_***''size''***
-[* 5] 1x panel_enc2_back_***''size''***
+[* 2] 2x panel_enc2_side_***''500''***
+[* 3] 1x panel_enc2_door_***''500''***
+[* 4] 1x panel_enc2_top_***''500''***
+[* 5] 1x panel_enc2_back_***''500''***
[* 10] Use the file with the correct ***''size''*** for your printer (200, 300, 400 or 500)