Pending Edits to 0.1 WorkBench 2.0 - 3D Printers
Note: Accepting or denying any edit implicitly applies to all earlier pending edits to the same step or introduction.
Step #1 edited: [Step edited]
Edited by Davide Depau (1)
(You don’t have enough reputation to patrol this edit.)
| [title] Recommended tools | |
| [* 10] It is recommended to have the following tools available for assembling the WorkBench 2.0 for 3D printers: | |
| - | [* 2] Allen Key |
| + | [* 2] Allen Key 6mm |
| [* 4] Tape measure or calipers | |
| [* 3] Engineers Square |
Step #7 edited: [Step edited]
Edited by Davide Depau (1)
(You don’t have enough reputation to patrol this edit.)
| [title] Prepare the remaining extrusions | |
| [* 2] 6x 470mm 4040 Extrusion | |
| [* 10] 670mm for the 750x800 WorkBench 2.0 | |
| + | [* 10] 770mm for the 850x900 WorkBench 2.0 |
| [* 3] 16x 4040 Cast Corners assemblies |
Step #13 edited: [Step edited]
Edited by Davide Depau (1)
(You don’t have enough reputation to patrol this edit.)
| [title] Table top | |
| [* 11] The table top is not included in the kit, you will have to source it locally. It is recommended to use a table top with a thickness no less than 20mm. The required dimensions are as follows: | |
| - | [* 1] For V-Core 200/300 - Workbench: 550x600mm |
| + | [* 1] For V-Core 200/300 - Workbench: 550x600mm |
| [* 1] For V-Core 200/300/400/500 - Workbench: 750x800mm | |
| + | [* 1] For V-Core 4 300/400 - Workbench: 850x900mm |
Step #9 edited: [Step edited]
Edited by Davide Depau (1)
(You don’t have enough reputation to patrol this edit.)
| [title] Assemble the side extrusions (x4) | |
| [* 2] 470mm 4040 Extrusion | |
| [* 10] 670mm for the 750x800 WorkBench 2.0 | |
| + | [* 10] 770mm for the 850x900 WorkBench 2.0 |
| [* 3] 4x 4040 cast corner | |
| [* 4] Check all of the cast corners to make sure they are flush with the extrusion ends | |
| [* 5] Secure the cast corners to the extrusion by fastening the four M8x16 screws | |
| [* 11] Repeat this step to create a total of four assemblies. |
Step #8 edited: [Step edited]
Edited by Davide Depau (1)
(You don’t have enough reputation to patrol this edit.)
| [title] Assemble the middle frame extrusions (x2) | |
| [* 2] 470mm 4040 Extrusion | |
| [* 10] 670mm for the 750x800 WorkBench 2.0 | |
| + | [* 10] 770mm for the 850x900 WorkBench 2.0 |
| [* 3] 4x 4040 cast corner | |
| [* 4] Check all of the cast corners to make sure they are flush with the extrusion ends | |
| [* 5] Secure the cast corners to the extrusion by fastening the four M8x16 screws | |
| [* 11] Repeat this step to create the second assembly. |
Step #6 edited: [Step edited]
Edited by Davide Depau (1)
(You don’t have enough reputation to patrol this edit.)
| [title] Prepare and Assemble the side frames (x2) | |
| [* 2] 8x 4040 Cast Corners assemblies | |
| [* 3] 4x 520mm 4040 Extrusion | |
| [* 10] 720mm for the 750x800 WorkBench 2.0 | |
| + | [* 10] 820mm for the 850x900 WorkBench 2.0 |
| [* 4] 4x 805mm 4040 Extrusion | |
| - | [* 10] 615mm for the 750x800 WorkBench 2.0 |
| + | [* 10] 615mm for the 750x800 and the 850x900 WorkBench 2.0 |
| [* 10] Assemble two side frames as shown. | |
| [* 9] Ensure the extrusions are flush and square with the 4040 cast corner assemblies before and after tightening the screws. |