You're viewing a previously published revision of this guide.  View latest revision

Older
Mar 20, 2025 - 02:03:15
May 06, 2025 - 03:05:19 May 06, 2025 - 03:05:02 May 06, 2025 - 01:05:33 May 06, 2025 - 01:05:37 May 06, 2025 - 01:05:57 May 06, 2025 - 01:05:06 May 06, 2025 - 01:05:23 Mar 24, 2025 - 07:03:42 Mar 24, 2025 - 07:03:57 Mar 24, 2025 - 07:03:34 Mar 24, 2025 - 07:03:27 Mar 24, 2025 - 07:03:55 Mar 24, 2025 - 07:03:50 Mar 24, 2025 - 07:03:14 Mar 24, 2025 - 07:03:38 Mar 24, 2025 - 05:03:15 Mar 24, 2025 - 05:03:09 Mar 24, 2025 - 05:03:35 Mar 24, 2025 - 05:03:20 Mar 24, 2025 - 05:03:16 Mar 24, 2025 - 05:03:55 Mar 24, 2025 - 05:03:36 Mar 24, 2025 - 05:03:10 Mar 21, 2025 - 07:03:24 Mar 21, 2025 - 07:03:22 Mar 21, 2025 - 07:03:18 Mar 21, 2025 - 07:03:03 Mar 21, 2025 - 06:03:22 Mar 21, 2025 - 02:03:47 Mar 21, 2025 - 02:03:41 Mar 21, 2025 - 02:03:11 Mar 21, 2025 - 02:03:07 Mar 21, 2025 - 02:03:03 Mar 21, 2025 - 02:03:32 Mar 20, 2025 - 10:03:40 Mar 20, 2025 - 10:03:17 Mar 20, 2025 - 10:03:00 Mar 20, 2025 - 10:03:51 Mar 20, 2025 - 02:03:15 Mar 20, 2025 - 02:03:24 Mar 17, 2025 - 10:03:23 Mar 17, 2025 - 10:03:31 Mar 17, 2025 - 10:03:26 Mar 17, 2025 - 10:03:19 Mar 17, 2025 - 09:03:04 Mar 17, 2025 - 09:03:27 Mar 17, 2025 - 09:03:24 Mar 17, 2025 - 09:03:28 Mar 17, 2025 - 09:03:07 Mar 17, 2025 - 09:03:53 Mar 17, 2025 - 09:03:16 Mar 17, 2025 - 09:03:08 Mar 17, 2025 - 09:03:53 Mar 17, 2025 - 09:03:21 Mar 17, 2025 - 09:03:50 Mar 17, 2025 - 09:03:29 Mar 17, 2025 - 09:03:53 Mar 17, 2025 - 08:03:38 Mar 17, 2025 - 08:03:50 Mar 17, 2025 - 08:03:18
Newer

05. Machine connections

Written By: Rat Rig
  • Comments: 0
  • Favorites: 0

Steps

5

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

Quiz

0

  1. Rat Rig Universal CNC Electronics Enclosure - rear

    • Rat Rig Universal CNC Electronics Enclosure - rear

    • 8x M5x12 Cap Head Screw

    • 8x M5 Washer

    • 8x 3030 Drop-in T-Nut - M5

    • 3x rubber grommets

  2. rubber grommets Insert a M5x12 Cap Head Screw and a M5 Washer into all the holes on the panel as shown

    • rubber grommets

    • Insert a M5x12 Cap Head Screw and a M5 Washer into all the holes on the panel as shown

    • Loosely tighten a 3030 Drop-in T-Nut - M5 into each screw.

  3. Feed all the stepper motor cables through the designated hole on the rear panel. Then insert them into the components upper panel slot, as shown. Connect them into the designated slots. Feed all the endstop cables through the designated hole on the rear panel. Then insert them into the components upper panel slot, as shown.

    • Feed all the stepper motor cables through the designated hole on the rear panel. Then insert them into the components upper panel slot, as shown.

    • Connect them into the designated slots.

    • Feed all the endstop cables through the designated hole on the rear panel. Then insert them into the components upper panel slot, as shown.

    • Connect them into the designated slots.

    • Feed the spindle cable through the designated hole on the rear panel. Then insert them into the components lower panel slot, as shown.

    • The cables should be inserted into the rear panel here.

    • Y2 Should only be connected if you are wiring a StrongHold Machine, it's not used in the Mill.

  4. Place all T-nuts inside the T-slot extrusions an tighten the screws, securing the rear panel to the assembly.

    • Place all T-nuts inside the T-slot extrusions an tighten the screws, securing the rear panel to the assembly.

  5. Connect the spindle cable to the VFD as shown, the wires are labed.

    • Connect the spindle cable to the VFD as shown, the wires are labed.

    • Crimp a Fork connector onto each wire before connecting it to the VFD

Author

Rat Rig

Member since: 7/10/20

48,550 Reputation

105 Guides authored

View Statistics:

Past 24 Hours: 17

Past 7 Days: 139

Past 30 Days: 737

All Time: 7,520