05. CoreXY Motor Assemblies

2x motor_plate

1x motor_support_left Printed Part

1x motor_support_right Printed Part

8x M6x12 Cap Head Screw

8x 3030 Drop-in T-Nut - M6

4x M5x40 Cap Head Screw

motor_plate

Make sure the motor plates are oriented as shown

motor_support_left Printed Part

M6x12 Cap Head Screw

3030 Drop-in T-Nut - M6

Loosely thread a 3030 T-Nut onto each of the M6x12 screws. Do not tighten them at this point.

motor_support_right Printed Part

Set the right motor plate assembly, and two M5x40 Cap Head Screws, aside until Step 12

V-Core 3.1 Frame Assembly - Rear Left Corner

Left motor_plate assembly from Step 2

Install the left motor_plate assembly to the V-Core 3.1 frame as shown

Tighten the four M6x12 screws to secure the motor_plate assembly to the frame

Make sure the plate is fully seated against the 3030 extrusion before tightening the M6x12 screws

Insert two M5x40 screws into the motor_plate, as shown, in preparation for Step 5

3x M6x14 Countersink Screw

3x 3030 Drop-in T-Nut - M6

1x xy_motor_cage_bottom_left_3.1 Printed Part

1x xy_motor_cage_top_left_3.1_cutout Printed Part

6x F695ZZ Ball Bearing

3x 695ZZ Ball Bearing

5x Mini Precision Shim

2x M5 Nylon Locking Hex Nut

Install the xy_motor_cage_bottom_left printed part as shown

Install the following components in the order shown in the image:

Mini Precision Shim

F695ZZ Ball Bearing (Flange at the bottom)

695ZZ Ball Bearing

F695ZZ Ball Bearing (Flange at the top)

Proper installation of the belt is very important, failure to follow the instructions can lead to damage of the belt

The CoreXY belt is provided in one continuous length. Unroll the belt and cut it in half to give you two belts of the same length

Position one half of the belt so that the toothed side faces the frame, and the smooth side faces the bearing stacks

Slot this half to the bottom of the CoreXY motor assembly, it should align with the bottom bearing stack

Take the other half of the CoreXY belt. Again, position the belt so that the toothed side faces the frame and the smooth side faces the bearing stacks

Form a loop as shown, this will be used to engage with the NEMA17 motor pulley

Position the upper belt as shown

Make sure that both belts match the third image before proceeding

3030 Drop-in T-Nut - M6

xy_motor_cage_top_left_3.1_cutout Printed Part

M6x14 Countersink Screw

Loosely thread a 3030 T-Nut onto each of the M6x14 screws. Do not tighten them at this point.

M5 Nylon Locking Hex Nut

Install the xy_motor_cage_left_top assembly onto the frame as shown

Make sure the belt loop, created in Step 6, remains in the position shown

Tighten the three marked M6x14 screws to secure the CoreXY motor cage top to the frame

Take care not to over tighten the M6x14 screws as you can damage the printed part

Tighten the M5x40 screws to secure the bearing stacks into the CoreXY motor cage top

1x 20 Tooth 2GT Timing Pulley for 9mm Belt

1x 48mm NEMA17 Stepper Motor

4x M3x35 Cap Head Screw

20 Tooth 2GT Timing Pulley for 9mm Belt

Install the timing pulley onto the NEMA17 shaft, oriented as shown

Align one of the M3 grub screws on the timing pulley so that it will tighten against the flat on the NEMA17 shaft

Position the timing pulley so the marked gap is 9.5mm

Slightly tighten one of the M3 grub screws to hold the timing pulley in position for now

The timing pulley will be aligned and fully secured in the next step

Position the NEMA17 motor up and into the motor cage from below, it will be secured in the next step

Insert the M3x35 screws into the xy_motor_cage_left_top as shown, and fasten them to secure the NEMA17 motor to the mount

Check the alignment of the timing pulley, the belt should be on the middle of the pulley as shown

Adjust the pulley up or down if required to make sure the belt is in the middle of the pulley

Fasten both M3 grub screws to securely mount the timing pulley to the NEMA17 motor shaft

V-Core 3.1 Frame Assembly - Rear Right Corner

Right motor_plate assembly from Step 2

Install the right motor_plate assembly to the V-Core 3.1 frame as shown

Tighten the four M6x12 screws to secure the motor_plate assembly to the frame

Make sure the plate is fully seated against the 3030 extrusion before tightening the M6x12 screws

Insert two M5x40 Cap Head Screws into the motor_plate, as shown, in preparation for Step 14

3x M6x14 Countersink Screw

3x 3030 Drop-in T-Nut - M6

1x xy_motor_cage_bottom_right_3.1 Printed Part

1x xy_motor_cage_top_right_3.1_cutout Printed Part

6x F695ZZ Ball Bearing

3x 695ZZ Ball Bearing

5x Mini Precision Shim

2x M5 Nylon Locking Hex Nut

V-Core 3.1 Frame Assembly - Rear Right Corner

Install the following components in the order shown in the image:

Mini Precision Shim

F695ZZ Ball Bearing (Flange at the bottom)

695ZZ Ball Bearing

F695ZZ Ball Bearing (Flange at the top)

xy_motor_cage_bottom_right_3.1 Printed Part

Place the xy_motor_cage_bottom_right_3.1_cutout printed part as shown

The xy_motor_cage_bottom_right part will just sit on the plate for now, it will be secured in Step 20

Loose end of the bottom CoreXY belt

Form a loop as shown, this will be used to engage with the NEMA17 motor pulley

Position the bottom belt as shown

Loose end of the top CoreXY belt

Slot this end of the top CoreXY belt around the top bearing stack as shown

Make sure that both belts match the third image before proceeding

3030 Drop-in T-Nut - M6

xy_motor_cage_top_right_3.1_cutout Printed Part

M6x14 Countersink Screw

Loosely thread a 3030 T-Nut onto each of the M6x14 screws. Do not tighten them at this point.

M5 Nylon Locking Hex Nut

Install the xy_motor_cage_right_top assembly onto the frame as shown

Tighten the three marked M6x14 screws to secure the CoreXY motor cage top to the frame

Tighten the M5x40 screws, on the underside, to secure the bearing stacks into the CoreXY motor cage top

1x 20 Tooth 2GT Timing Pulley for 9mm Belt

1x 48mm NEMA17 Stepper Motor

4x M3x35 Cap Head Screw

20 Tooth 2GT Timing Pulley for 9mm Belt

Install the timing pulley onto the NEMA17 shaft, oriented as shown

Align one of the M3 grub screws on the timing pulley so that it will tighten against the flat on the NEMA17 shaft

Position the timing pulley so the marked gap is 3mm

Slightly tighten one of the M3 grub screws to hold the timing pulley in position for now

The timing pulley will be aligned and fully secured in the next step

Position the NEMA17 motor up and into the motor cage from below, it will be secured in the next step

Insert the M3x35 screws into the xy_motor_cage_right_top_3.1_cutout as shown, and fasten them to secure the NEMA17 motor to the mount

Check the alignment of the timing pulley, the belt should be on the middle of the pulley as shown

Adjust the pulley up or down if required to make sure the belt is in the middle of the pulley

Fasten both M3 grub screws to securely mount the timing pulley to the NEMA17 motor shaft